• ALUMA HYDE II AERSOL BROWNELLS More Detail

    ALUMA HYDE II AERSOL BROWNELLS

    $12.99 - $14.99$12.99 - $14.99

    Protect Your Guns Finish From Chemical Bore Cleaners Protects your finish from aggressive chemical solution bore cleaners that contact other parts of your gun during maintenance. Hard-curing epoxy sticks to all properly prepared aluminum, steel, plastic & synthetic stock surfaces. Available in a wide variety of colors to match your weapon. Made in the U.S.A. Brownells Guntechs recommend use of 084-179-004 All Purpose Clean Out Nozzle prior to attempting to spray this product.

    HOT!
  • AR-15/M16 RECEIVER ACTION BLOCK BROWNELLS More Detail

    AR-15/M16 RECEIVER ACTION BLOCK BROWNELLS

    $59.99 - $79.99$59.99 - $79.99

    Protect Receiver From Damage When Clamping Hold rifle firmly for safe, effective cleaning, assembly, & repair. Apply vise pressure or torque the barrel nut without crushing, twisting, or otherwise distorting receiver halves. Transforms rebarreling the AR-15/M16 an easy, one-man job. Minimizes potential damage to the barrel detent pin & receiver detent notch. DO NOT USE ON BILLET UPPERS OR DAMAGE TO THE UPPER CAN RESULT

    HOT!
  • ROLL PIN HOLDERS BROWNELLS More Detail

    ROLL PIN HOLDERS BROWNELLS

    $14.99 - $49.99$14.99 - $49.99

    Hollow-Ended "Starter" Punches For Roll PinsHolds roll pins perfectly aligned for starting correctly. Especially good on the tiny, tough-to-grab ones, or those in tight places. 1/16" is notched to clear M16/AR-15 rear sight. 3.5mm excellent for holding the pin that retains the breech block on Sig handguns. Finish driving with roll pin punch. O/A in chart means "Overall". Available individually or as a set of 5.

    HOT!
  • AR-15/M16 LOWER RECEIVER VISE BLOCK BROWNELLS More Detail

    AR-15/M16 LOWER RECEIVER VISE BLOCK BROWNELLS

    $49.99 - $79.99$49.99 - $79.99

    Protect Receiver From Damage When Clamping Heavy-duty blocks allow you to firmly clamp AR-15/M16 receiver halves in a vise without risk of crushing, twisting, or otherwise distorting them when applying vise pressure or torquing the barrel nut. Keeps your rifle secure for safe, effective cleaning, assembly, and repair. Unbreakable urethane vise block takes all the clamping force, so your expensive lower receiver won’t be damaged or distorted. Insert block into the magazine housing from the top or bottom, then clamp the other end in your bench vise. The magazine catch locks to the block, safely and securely holding the rifle for assembly, disassembly, cleaning, or repair. Will not mar or scratch the finish. Fits tightly in most receivers and may require filing to fit others. 

    HOT!
  • SEMI-AUTO SIGHT MOVER MGW More Detail

    SEMI-AUTO SIGHT MOVER MGW

    $129.99$129.99

    Adjusts, Removes & Installs Sights Without Damage Safely moves fixed sights right or left in their dovetails without deforming slide or sight. Specifically designed for use with factory and aftermarket Tritium night sights, which are too fragile for the traditional hammer-and-punch sight installation method; works equally well with iron sights. Thumbscrew securely locks the slide so it’s fully supported in the rigid, machined aluminum body. Separate slots in the screw mechanism engage the sight and firmly, yet gently, concentrate screw force to loosen sights from even extremely tight dovetails. Hardened steel handle provides plenty of leverage, while self-lubricating, oil-impregnated Oilite® bronze bearings and extra-fine threads ensure smooth, precise movement. Beretta/Glock fit rear sights only. Glock Flat-Side fits aftermarket rear sights with straight, non-sloped sides for standard- and large-frame Glock pistols. SIG fits rear sights on all SIGs except SIG-PRO. Smith & Wesson M&P fits both and front and rear sights; will not fit Pro models with 5" barrel. Will not fit the Shield model. Separate Shield model available. Springfield XD fits both front and rear sights on all XD models except front sight on 5" barrel Tactical model. These do not work on the front sights of Pro/Tactical or sub compact XD/XDM model front sights. Will not work on XD-S slides. 1911 will not work with most Kimber slide/sight combinations. Only works on rear sights. Not for installing or adjusting front sights. Sig fits P220, P225, P226, P228, P239 only. Does not fit Sig Pro series. Does not fit P220 Elite Shadow. Does not work on adjustable sights. Glock 42 Adapter Kit fits the MGW309 and MGW309S Sight Movers to fit the new compact Glock 42 pistols. The adapter kit includes the adapter spacer and the shoe. “GLOCK” is a federally registered trademark of Glock, Inc. and is one of many trademarks owned by Glock, Inc. or Glock Ges.m.b.H.  Brownells is an independent dealer of parts and accessories for Glock® pistols, and is not affiliated with or endorsed by Glock, Inc. or Glock Ges.m.b.H.  The use of Glock on this page is merely to advertise the sale of Glock parts or components.  As indicated in the product descriptions, not all parts and accessories on this site are official Glock products.

    HOT!
  • RIFLE BENCH BLOCK BROWNELLS More Detail

    RIFLE BENCH BLOCK BROWNELLS

    $19.99$19.99

    Easily Drive Pins Without All The Balancing Act Wont mar even the most highly polished surface. Easily drive pins without all the balancing actbig face, plus extra size and weight means these blocks stay where you put them. Made in the U.S.A.

    HOT!
  • #565 PIN PUNCH SET STARRETT More Detail

    #565 PIN PUNCH SET STARRETT

    $6.49 - $6.99$6.49 - $6.99

    Precision Ground-Beautifully PolishedPrecision ground from specially selected tool steel, hardened and highly polished, the Starrett Pin Punches are well proportioned and beautifully finished. Blued, knurled grip area; individually marked for size. Set of all 8 punches comes in handy, fitted, round, plastic bench box. Also available singly.

    HOT!
  • AR-15/M16/M4 ARMORER'S KITS BROWNELLS More Detail

    AR-15/M16/M4 ARMORER'S KITS BROWNELLS

    $999.99$999.99

    Complete Kits To Service Law Enforcement AR-Type RiflesSave Time With The Right Tools For The Job The RIGHT way to service the AR-15/M16/M4 with all the tools needed to perform full maintenance and repair in the field or shopSaves you time by having the right tool for the jobStandard kit contains the tools needed to work on AR-15 and the M16A1 through M16A4 riflePremium kit contains all the tools of the Standard kit, plus 11 additional tools specifically needed for the M4 carbineBoth kits come in a custom-fitted, hard-side tool box that meets mil-spec MIL-C-4150 & ATA specifications

    HOT!
  • MAGNA-TIP® PROFESSIONAL SUPER SET BROWNELLS More Detail

    MAGNA-TIP® PROFESSIONAL SUPER SET BROWNELLS

    $329.99 - $419.99$329.99 - $419.99

    Professional Grade Selection Of 120 Magna-Tip Bits No more custom grinding bits for a proper fit, or wasted time waiting for a specialty screwdriver to arrive. Proper-fitting bits prevent damage to screw slotsa sure sign of truly top-notch gunsmithing work. Includes 75 straight, 4 Phillips, 17 hex (Allen), 11 Torx, and 13 specialty bits for sights, scope mounts, grip bushings, Ruger ejectors, and other unique applications, plus the handy Magna-Tip Choke Tube Wrench and a hex-to-square adapter that lets you use your Magna-Tip handles to drive " drive sockets. Made in the U.S.A.

    HOT!
  • AR-15 FRONT SIGHT BENCH BLOCK BROWNELLS More Detail

    AR-15 FRONT SIGHT BENCH BLOCK BROWNELLS

    $39.99$39.99

    Two Working Sides For Installation & Removal Fitted support for installation or removal of front sight assembly on mil-spec, AR-15 rifles & carbines. Simplifies driving the mounting pins IN or OUT of the sight. Works with sling swivel, plus, includes provisions for removing the gas tube roll pin. Made in the U.S.A.

    HOT!
  • SIGHT INSTALLATION TOOL for GLOCK® TRIJICON More Detail

    SIGHT INSTALLATION TOOL for GLOCK® TRIJICON

    $139.99$139.99

    Install, Adjust & Remove Glock Sights Without Damage Specifically designed to install, adjust and remove all models of Trijicon Glock Sights without damage. Includes heavy-duty rear sight mover with oilite bushings that allow for very fine windage adjustments, and a front sight nut driver that fits all models of aftermarket front sights. “GLOCK” is a federally registered trademark of Glock, Inc. and is one of many trademarks owned by Glock, Inc. or Glock Ges.m.b.H.  Brownells is an independent dealer of parts and accessories for Glock® pistols, and is not affiliated with or endorsed by Glock, Inc. or Glock Ges.m.b.H.  The use of Glock on this page is merely to advertise the sale of Glock parts or components.  As indicated in the product descriptions, not all parts and accessories on this site are official Glock products.

    HOT!
  • AR-15/M16 SIGHT WRENCH BROWNELLS More Detail

    AR-15/M16 SIGHT WRENCH BROWNELLS

    $9.99$9.99

    Quick & Easy Sight Adjusting Get the tool designed specifically for the job, no more wasting time trying to use a round of ammo to make important sight adjustments. Made in the U.S.A.

    HOT!
  • MAGNETIC SOFT JAWS WAGNER INDUSTRIES INC More Detail

    MAGNETIC SOFT JAWS WAGNER INDUSTRIES INC

    $39.99 - $48.99$39.99 - $48.99

    Turn Any Vise Into A Gun-Friendly Precision Tool Add soft, yet extremely rigid, polyurethane vise jaws to any 4" or 5" visenon-slip surface grips valuable firearms firmly without crushing, marring, or scratching. Held in place by embedded magnets. Includes separate polyurethane cover for vise screws or anvils for added protection.

    HOT!
  • ROLL PIN PUNCHES BROWNELLS More Detail

    ROLL PIN PUNCHES BROWNELLS

    $4.99$4.99

    Only Way You Can Remove Pins And Not Damage ThemWith these pins becoming so common in guns, having the right punches to remove them is absolutely necessary. These punches are the only way to remove and re-use roll or spring pins without causing glaring damage to the pins. Solid steel punches, with long, parallel-ground points and knurled section for better gripping.

    HOT!
  • P500 UNIVERSAL SIGHT TOOL B & J MACHINE More Detail

    P500 UNIVERSAL SIGHT TOOL B & J MACHINE

    $139.99$139.99

    Safely Removes & Installs Dovetail Front & Rear Sights; Works On Shallow, Cross-Dovetails Precision-machined, steel tool safely removes, installs and adjusts front and rear sights on handguns. Clamp your slide into the tool and line up the sights with the tool’s pusher tip for installation, removal, or adjustment. Mobile jaw customizes to the height of your slide and can be used from the right or left side. Delrin® liner protects slide from scratches. Includes three sight pushers that attach to the end of the sight-pushing bolt. 1⁄4" square tip works perfectly on shallow, cross-dovetail sights. Hold Down Clamp helps prevent the slide from twisting in the frame of the P500 by applying extra force to the top of the slide. Provides a secure seat in the tool when working with hard-to-remove sights or slides with angled sides, like the Springfield Armory XD and the S&W M&P. Slide Stop speeds up the process of performing the same sight job on a large number of the same model pistol. Stop simply screws to the P500 frame and lets you position each slide in exactly the same place to perform the necessary sight adjustment quickly and easily. P500 Universal Sight Tool Kit combines P500 Universal Sight Tool with the Hold Down Clamp and Slide Stop to provide the ultimate of flexibility and versatility in a sight adjustment tool.

    HOT!
  • BROWNELLS MULTI-VISE BROWNELLS More Detail

    BROWNELLS MULTI-VISE BROWNELLS

    $299.99$299.99

    Extreme Versatility In A High-Strength Bench Vise Adjust this vise in every direction a job can take you easily position the multi-vise horizontally, vertically, and rotate it 360 in a horizontal plane. No need to tighten or loosen extra clamps when you turn Multi-Vise on its side or rotate it - convenient cam locking system automatically holds Multi-Vise in position when you tighten the jaw.

    HOT!
  • CUP TIP PUNCHES BROWNELLS More Detail

    CUP TIP PUNCHES BROWNELLS

    $11.99 - $12.99$11.99 - $12.99

    Prevent Those Beautiful Round-Headed Pins From Flat-Topping Eight concave “cupped” tip punches to precisely fit the round head pins found on Smith & Wesson handguns. Won’t flatten the pin top and ruin the gun’s looks. Made to the same specs as those used by the factory. Use 3mm punch on SIG handguns. Complete set (Set D listed below) includes a Delrin® bench block that holds and organizes all eight punches. Bench block also available separately 080-000-644.

    HOT!
  • AR-15/M16 ARMORER'S TOOL TAPCO WEAPONS ACCESSORIES More Detail

    AR-15/M16 ARMORER'S TOOL TAPCO WEAPONS ACCESSORIES

    $39.99$39.99

    Like A One-Piece Tool Kit Handy all-in-one tool handles the tasks necessary to build and maintain your AR-15 or M16. It's a barrel nut wrench, muzzle device wrench, spanner wrench, forearm wrench, flat tip screwdriver, A2 tube remover, receptacle for ½" drive/torque wrench - and a bottle opener. Long handle give plenty of leverage for buttstock and barrel removal/installation, and the ½" drive receptacle allows the use of a torque wrench, so you can get things tightened down correctly. It even has a flat face on one side that can be used as a hammer.

    HOT!
  • 1911 AUTO ANODIZED BUSHING WRENCH BROWNELLS More Detail

    1911 AUTO ANODIZED BUSHING WRENCH BROWNELLS

    $19.99$19.99

    Turns The Tightest Bushings Without Slipping Closely fits Government Model & Officers bushings. Plenty of heft for solid hand grip. Made in the U.S.A..

    HOT!
  • 1911 AUTO ARMORER'S BLOCK 10-8 PERFORMANCE LLC More Detail

    1911 AUTO ARMORER'S BLOCK 10-8 PERFORMANCE LLC

    $49.99$49.99

    Fast Easy Maintenance Platform Protects Pistol Finish Securely holds pistol frame on its side, so you can work on it without risk of damaging the finish. Gives solid support & stability for precision adjustments or maintenance. Built-in blind holes catch link pins during removal so they dont get lost.

    HOT!
  • REMINGTON 870 SERVICE KIT BROWNELLS More Detail

    REMINGTON 870 SERVICE KIT BROWNELLS

    $339.99 - $359.99$339.99 - $359.99

    All The Right Factory-Type Tools To Keep 870s RunningEverything to take apart 870s, make the necessary repairs or adjustments, and put them back togetherIncludes specialized tools adapted from factory designs with input from the folks at Remington870-specific tools: forend wrench, magazine spring retainer tool, Menck magazine corkscrew tool, trigger group pin pusher, ejector spring/housing rivet staking tool set, shell plate latch staker, buttstock bolt wrenchOther tools: Magna-Tip driver handle with a set of 870-specific screwdriver bits, pin punch set, nylon/brass hammer, cleaning brushes, a bench mat, and moreComes in a hard polymer tool box with plenty of room for the entire kit, plus some extra tools of your own

    HOT!
  • AR-15/M16 CARBINE STOCK WRENCH ROCK RIVER ARMS More Detail

    AR-15/M16 CARBINE STOCK WRENCH ROCK RIVER ARMS

    $9.99$9.99

    Install M4 Carbine Stocks Without Damage Easily remove your old extension tube & install a new-style, A4 stock Non-slip fit so you can correctly torque the stock to the receiver.

    HOT!
  • SKS/AK-47 FRONT SIGHT TOOL TAPCO WEAPONS ACCESSORIES More Detail

    SKS/AK-47 FRONT SIGHT TOOL TAPCO WEAPONS ACCESSORIES

    $16.49$16.49

    All Steel, Adjusts Windage & ElevationPrecision machined, all steel C-clamp easily adjusts front sight windage and elevation on most AK-47 and SKS variants. Threaded T-handle provides the force needed to move even stubborn front sights. Opposite end of T-handle fits elevation post. Made in the U.S.A.

    HOT!
  • BROKEN SHELL EXTRACTOR BROWNELLS More Detail

    BROKEN SHELL EXTRACTOR BROWNELLS

    $19.99$19.99

    Easily Removes Broken Cases Without Field Stripping Keep one of these handy tools in your pocket or field kit. Simply drop into the chamber and close the boltdraw back the bolt to open the chamber & the broken case will eject along with the tool. Two-piece design adjusts for length, so the tool completely engages the rim of the case mouth; cannot slip through or strip out. Made in the U.S.A.

    HOT!

Subscribe our newsletter

Lorem ipsum dolor sit amet, consectetur adipisicing elit. Ex, velit!